# This file allows user to override the factory
# defaults for the WLAN Driver

# Phy Mode (auto, b, g, n, etc)
# Valid values are 0-12, with 0(Min) = Auto, 12(Max) = 11ax
# 1 = 11abg, 2 = 11b, 3 = 11g, 4 = 11n, 5 = 11g only, 6 = 11n only
# 7 = 11b only 8 = 11ac only, 9 = 11ac, 12 = 11ax.
gDot11Mode=0
twt_responder=0
#Enable Modulated DTIM
gEnableModulatedDTIM=3

#Max modulated DTIM
gMaxLIModulatedDTIM=5

# UAPSD service interval for VO,VI, BE, BK traffic
InfraUapsdVoSrvIntv=0
InfraUapsdViSrvIntv=0
InfraUapsdBeSrvIntv=0
InfraUapsdBkSrvIntv=0

# Flag to allow STA send AddTspec even when ACM is Off
gAddTSWhenACMIsOff=1

#Enable OBSS protection
gEnableApOBSSProt=1

# Maximum Tx power
# gTxPowerCap=30

# Fragmentation Threshold
# gFragmentationThreshold=2346

# RTS threshold
RTSThreshold=1048576

# WMM Enable/Disable
WmmIsEnabled=0

# 802.11d support
g11dSupportEnabled=0

# DFS Master Capability
gEnableDFSMasterCap=1

ImplicitQosIsEnabled=0

gNeighborScanTimerPeriod=45
gNeighborLookupThreshold=75

# Legacy (non-ESE, non-802.11r) Fast Roaming Support
# To enable, set FastRoamEnabled=1
# To disable, set FastRoamEnabled=0
FastRoamEnabled=1

#Channel Bonding
gChannelBondingMode5GHz=1

is_bssid_hint_priority =1

#Say gGoKeepAlivePeriod(5 seconds) and gGoLinkMonitorPeriod(10 seconds).
#For every 10 seconds DUT send Qos Null frame(i.e., Keep Alive frame if link
#is idle for last 10 seconds.) For both active and power save clients.

#Power save clients: DUT set TIM bit from 10th second onwards and till client
#honors TIM bit. If doesn't honor for 5 seconds then DUT remove client.

#Active clients: DUT send Qos Null frame for 10th seconds onwards if it is not
#success still we try on 11th second if not tries on 12th and so on till 15th
#second. Hence before disconnection DUT will send 5 NULL frames. Hence in any
#case DUT will detect client got removed in (10+5) seconds.
#i.e., (gGoKeepAlivePeriod + gGoLinkMonitorPeriod)..

#gGoLinkMonitorPeriod/ gApLinkMonitorPeriod is period where link is idle and
#it is period where we send NULL frame.
#gApLinkMonitorPeriod = 10
#gGoLinkMonitorPeriod = 10

#gApKeepAlivePeriod is time to spend to check whether frame
#are succeed to send or not. Hence total effective detection time is
#(gApLinkMonitorPeriod + gApKeepAlivePeriod)

#STA Keepalive Period 	
gStaKeepAlivePeriod=15

# Enable DFS channel roam
# 0: DISABLE, 1: ENABLED_NORMAL, 2: ENABLED_ACTIVE
gAllowDFSChannelRoam=1

gVhtChannelWidth=2

# Set txchainmask and rxchainmask
# These parameters are used only if gEnable2x2 is 0
# Valid values are 1,2
# Set gSetTxChainmask1x1=1 or gSetRxChainmask1x1=1 to select chain0.
# Set gSetTxChainmask1x1=2 or gSetRxChainmask1x1=2 to select chain1.
gSetTxChainmask1x1=1
gSetRxChainmask1x1=1

# MCC to SCC Switch mode:
# 0-Disable
# 1-Enable
# 2-Force SCC if same band, with SAP restart
# 3-Force SCC if same band, without SAP restart by sending (E)CSA
# 4-Force SCC if same band (or) use SAP mandatory channel for DBS,
#   without SAP restart by sending (E)CSA
gWlanMccToSccSwitchMode = 4

# 1=enable tx STBC; 0=disable
gEnableTXSTBC=1

#Enable/Disable Tx beamformee in SAP mode
gEnableTxBFeeSAP=1

# Enable Tx beamforming in VHT20MHz
# Valid values are 0,1. If commented out, the default value is 0.
# 0=disable, 1=enable
gEnableTxBFin20MHz=1

#Enable/Disable SU Tx beamformer support
gEnableTxSUBeamformer=1

# 802.11K support
gRrmEnable=1

# Firmware log mode
# Valid values are 0,1,2
# 0=Disable, 1=WMI, 2=DIAG
gEnablefwlog=1

# Maximum Receive AMPDU size (VHT only. Valid values:
# 0->8k 1->16k 2->32k 3->64k 4->128k)
gVhtAmpduLenExponent=7

# Maximum MPDU length (VHT only. Valid values:
# 0->3895 octets, 1->7991 octets, 2->11454 octets)
gVhtMpduLen=2

#Enable or Disable p2p device address administered
isP2pDeviceAddrAdministrated=1

#Enable VHT on 2.4Ghz
gEnableVhtFor24GHzBand=1

#Maximum number of offload peers supported
# gMaxOffloadPeers=2

# controlling the following offload patterns
# through ini parameter. Default value is 1
# to disable set it to zero. ssdp = 0
# Setup multicast pattern for mDNS 224.0.0.251,
# SSDP 239.255.255.250 and LLMNR 224.0.0.252
ssdp=0

# RA filtering rate limit param, the current value would not
# help if the lifetime in RA is less than 3*60=3min. Then
# we need to change it, though it is uncommon.
# gRAFilterEnable=0
gRArateLimitInterval=600

# Maximum number of concurrent connections
gMaxConcurrentActiveSessions=3

# Disable/Enable GreenAP
# 0 to disable, 1 to enable, default: 1
gEnableGreenAp=0

#Enable/Disable LPASS support
# 0 to disable, 1 to enable
gEnableLpassSupport=1

# Whether userspace country code setting shld have priority
gCountryCodePriority=1

# Enable or Disable Multi-user MIMO
# 1=Enable (default), 0=Disable
gEnableMuBformee=1

# Enable support for TDLS
#  0 - disable
#  1 - enable
gEnableTDLSSupport=1

# Enable support for Implicit Trigger of TDLS. That is, wlan driver shall
# initiate TDLS Discovery towards a peer whenever setup criteria (throughput
# and RSSI) is met and then will initiate teardown when teardown criteria
# (idle packet count and RSSI) is met.
#  0 - disable
#  1 - enable
gEnableTDLSImplicitTrigger=1

# Changed to 0 for Samsung to enable explicit TDLS withough supplicant change
# Enable TDLS External Control. That is, user space application has to
# first configure a peer MAC in wlan driver towards which TDLS is desired.
# Device will establish TDLS only towards those configured peers whenever
# TDLS criteria (throughput and RSSI threshold) is met and teardown TDLS
# when teardown criteria (idle packet count and RSSI) is met. However,
# device will accept TDLS connection if it is initiated from any other peer,
# even if that peer is not configured.
#  0 - disable
#  1 - enable
# For TDLS External Control, Implicit Trigger must also be enabled.
gTDLSExternalControl=0

# Changed to 0 for Samsung to disable TDLS offchannel
# Enable support for TDLS off-channel operation
#  0 - disable
#  1 - enable
# TDLS off-channel operation will be invoked when there is only one
# TDLS connection.
gEnableTDLSOffChannel=0

gSoftApMaxPeers=8
gTDLSMaxPeerCount=1

# Enable Mutiple TDLS links
gEnableTDLSBufferSta=0 
gTDLSUapsdMask=0
gTDLSRSSITeardownThreshold=-95

# TDLS Packet Threshold
gTDLSTxPacketThreshold=200

# VHT Tx/Rx MCS values
# Valid values are 0,1,2. If commented out, the default value is 0.
# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9
gVhtRxMCS=2
gVhtTxMCS=2

# VHT Tx/Rx MCS values for 2x2
# Valid values are 0,1,2. If commented out, the default value is 0.
# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9
gEnable2x2=1
gVhtRxMCS2x2=2
gVhtTxMCS2x2=2

#IPA config is a bit mask and following are the configurations.
#bit0 IPA Enable
#bit1 IPA PRE Filter enable
#bit2 IPv6 enable
#bit3 IPA Resource Manager (RM) enable
#bit4 IPA Clock scaling enable
#bit5 IPA uC ENABLE
#bit6 IPA uC STA ENABLE
#bit8 IPA Real Time Debugging
gIPAConfig=0
gIPADescSize=800

# Increase TCL ringsize
dp_tx_ring_size=3072

#Disable HW checksum for Legacy modes 
legacy_mode_csum_disable=1

# Enable TCP Segmentation Offload
# 1 - enable  0 - disable
TSOEnable=1

# Enable Generic Receive Offload
# 1 - enable(default)  0 - disable
GROEnable=1

# Enable HT MPDU Density
# 4 for 2 micro sec
ght_mpdu_density=4

# Enable flow steering to enable multiple CEs for Rx flows.
# Multiple Rx CEs<==>Multiple Rx IRQs<==>probably different CPUs.
# Parallel Rx paths.
# 1 - enable 0 - disable(default)
gEnableFlowSteering=1

# Enable Rx FISA support
# 0 - disable(default for non-QCA6490), 1 - enable(default for QCA6490)
dp_rx_fisa_enable=0

# Maximum number of MSDUs the firmware will pack in one HTT_T2H_MSG_TYPE_RX_IN_ORD_PADDR_IND
maxMSDUsPerRxInd=8

################ Datapath feature set End ################

################ NAN feature set start ###################

# Enable NAN discovery (NAN 1.0)
# 1 - enable  0 - disable(default)
gEnableNanSupport=1
# Enable NAN Datapath
genable_nan_datapath=1

################ NAN feature set end #####################

hostscan_adaptive_dwell_mode=1

# Enable/Disable rtt sta mac randomization
enable_rtt_mac_randomization=1

#Enable/Disable SNR monitoring
gEnableSNRMonitoring=1

gEnableConcurrentSTA=wlan1
gEnableSAPManadatoryChanList=1

# HTC Credit count for WMI operation
# 1 to serialize the WMI commands
# 0 default works with FW advertised credits, 2 credits usually
gWmiCreditCount=1

# Added for Samsung HST
# For enabled 11ac SAP
gSAP11ACOverride=1
# Enable enhanced ACS
acs_with_more_param=1
# bits 0-3:   rssi weight
# bits 4-7:   bss count weight
# bits 8-11:  noise floor weight
# bits 12-15: channel free weight
# bits 16-19: tx power range weight
# bits 20-23: tx power throughput weight
# bits 24-31: reserved
AutoChannelSelectWeight=0x00fafafa

# Enable/Disable broadcast TWT
bcast_twt=1

#Disable twt    
twt_congestion_timeout=0

# Enable Runtime PM
# 0 - RTPM disabled, so CxPC aware RTPM will be disabled as well
# 1 - RTPM enabled, but CxPC aware RTPM disabled (i.e, Static Runtime PM)
# 2 - RTPM enabled and CxPC aware RTPM enabled as well (i.e, Dynamic Runtime PM)
gRuntimePM=0	
gRuntimePMDelay=500

# QMI stats
enable_qmi_stats=0

# sae connect retry
sae_connect_retries=0x52

# join retry timer on failure
join_failure_retry_interval=1000

gActiveMaxChannelTime=80
active_max_channel_time_6g=60
passive_max_channel_time_6g=60

# Enable broadcast logging to the userspace entities
gMulticastHostFwMsgs=1
# Disable packetlog explicitly
gEnablePacketLog=0

# Set IPA bandwidth levels in mbps
gIPALowBandwidthMbps=100
gIPAMediumBandwidthMbps=400
gIPAHighBandwidthMbps=800

# Enable wlm_latency_enable feature
# 0 - disable, 1 - enable(default)
wlm_latency_enable=1
wlm_latency_flags_low=0x420000 
wlm_latency_flags_ultralow=0x420000
spectral_disable=1

# This ini is used to give higher priority for 5g scc than dbs.
# It is bitmap per enum policy_mgr_con_mode.
# For example in GO+STA(5G) mode, when TPUT is onfigured as wlan system
# preference option, If 5G SCC needs higher priority than dbs, set it as 8.
g_prefer_5g_scc_to_dbs=8

# To get PCIe debug info
gEnableSelfRecovery=1
#Roaming enhancements related ini
enable_bss_load_roam_trigger=1
bss_load_threshold=70
bss_load_sample_time=10000
bss_load_trigger_2g_rssi_threshold=-60
bss_load_trigger_5g_rssi_threshold=-70
enable_idle_roam=1
idle_roam_band=1
idle_roam_inactive_time=10
idle_roam_min_rssi=-60
idle_roam_rssi_delta=5
idle_data_packet_count=5
enable_disconnect_roam_offload=1
enable_adaptive_11r=1
gNeighborLookupThreshold=75
gEmptyScanRefreshPeriod=10000
roam_scan_inactivity_time=10000
roam_scan_period_after_inactivity=120000
roam_inactive_data_count=5
roam_score_delta=20
roam_score_delta_bitmap=0xFFFFFFFF
btm_roam_score_delta=0
idle_roam_score_delta=1
candidate_min_rssi_for_beacon_miss=-76
candidate_min_rssi_for_disconnect=-76
btm_disassoc_timer_threshold=10000
nr_offload_params_bitmask=1
nr_offload_time_offset=1
btm_offload_config=449
roam_candidate_validity_timer=0
minimum_btm_candidate_score=6000
roam_bad_rssi_thresh_offset_2g=0
roam_bg_scan_client_bitmap=0
rssi_weightage=65
channel_congestion_weightage=35
ht_caps_weightage=0
vht_caps_weightage=0
he_caps_weightage=0
chan_width_weightage=0
nss_weightage=0
chan_band_weightage=0
beamforming_cap_weightage=0
pcl_weightage=0
oce_wan_weightage=0
vendor_roam_score_algorithm=1
gNeighborScanChannelMaxTime=40
gRoamScanHomeAwayTime=100
RoamRssiDiff=10
gFullRoamScanPeriod=120
gRoamScanNProbes=2
gWESModeEnabled=0
min_roam_score_delta=1500
gper_roam_enabled=0
groam_dense_rssi_thresh_offset=0
gRoamScanHiRssiDelta=0
gChannelBondingMode24GHz=1
sae_single_pmk_feature_enabled=1 
gDroppedPktDisconnectTh=0
gEnableNUDTracking=0

#gEnableIpTcpUdpChecksumOffload=0
gHandleLatencyCriticalClients=1

etsi13_srd_chan_in_master_mode=7

#acquire wake lock during user scan
wake_lock_in_user_scan=1

enable_tcp_param_update=1

#Removed by request of SS 
#enable_bcn_rpt_err_vsie=1

#Removed by request of SS 
#enable_roam_reason_vsie=1

sta_disable_roam=3

#Enable PNO on R-OS
gPNOScanSupport=1

END

# Note: Configuration parser would not read anything past the END marker

